LAISARSV4 Factory 2024
Track: Circuito de Navarra
← Back to Circuito de NavarraTaken over from the track: Asphalt · Technical · Fast · dry
Aprilia RSV4 Factory 2024 - 75 kg, Intermediate, Neutral, Circuito de Navarra
Set this first
Transmission: Rear sprocket
- Stock value
- 41 teeth
- Recommended
- 40 teeth
- Change
- 1 tooth less than stock
Reason: condition Circuito de Navarra
How to test it: Change Rear sprocket only, nothing else. Then ride the same section or the same number of laps as before and watch whether exactly the behaviour that bothers you changes. If it gets worse or less settled, put the value back.
- Transmission: Rear sprocket40 teeth1 tooth less than stockcomputed
- Shock: Sag25 mmOEM
- Fork: Sag35 mmOEM
- Tire: Front tire pressure2.1 barOEM
- Tire: Rear tire pressure1.7 barOEM
19 confirmed settings available.
Computed from factory specs and your factors
Last reviewed: no release date - this starting value was computed, not measured.
A starting point to verify on the bike - not a safety guarantee. Change one thing at a time and check on track. How LAISA derives this →
All recommended changes
In order, biggest deviation from the stock value first. Take them one at a time.
- Transmission: Rear sprocket1 tooth less than stock
41 teeth40 teeth
Reason: condition Circuito de Navarra
How to test it
Change Rear sprocket only, nothing else. Then ride the same section or the same number of laps as before and watch whether exactly the behaviour that bothers you changes. If it gets worse or less settled, put the value back.
All technical values
Complete settings, technical data, components, gearing and geometry - including the adjusters that exist on the bike but do not carry a confirmed value yet.
| BrakeBrembo Radial Master Cylinder (Front) | ||
| Brake lever position | 3 notch | OEM |
| ChainOEM Chain | ||
| Chain length | 112 links | OEM |
| ChassisOEM Adjustable Chassis | ||
| Pivot Position | standard | OEM |
| Fork height in clampstube protrusion above top clamp | 4 ring | OEM |
| Rear ride heightshock length adjustment | 0 mm | OEM |
| ClutchOEM Wet Slipper Clutch | ||
| Clutch lever position | 3 notch | OEM |
| ECUMagneti-Marelli ECU (APRC) | ||
| ForkÖhlins NIX-30 (Smart EC 2.0) | ||
| Oil heightfrom top, fully compressed, no spring | 85 mm | OEM |
| Sagloaded, rider in gear | 35 mm | OEM |
| Spring rate | 10 N/mm | OEM |
| HandlebarOEM Handlebar | ||
| ShockÖhlins TTX36 (Smart EC 2.0) | ||
| Sagloaded, rider in gear | 25 mm | OEM |
| Static sagwithout load | 8 mm | OEM |
| Length | 312 mm | OEM |
| Spring rate | 95 N/mm | OEM |
| SwingarmOEM Aluminium Swingarm | ||
| Rear Axle PostionOffset from middle of adjustment range | 0 mm | OEM |
| TirePirelli Diablo Supercorsa SP | ||
| Front tire pressure | 2.1 bar (30.46 psi) | OEM |
| Rear tire pressure | 1.7 bar (24.66 psi) | OEM |
| TransmissionOEM Final Drive | ||
| Front sprocket | 16 teeth | OEM |
| Rear sprocket | 40 teeth▼ -1 | computed |
| Triple ClampOEM CNC Triple Clamp | ||
| Offset | 30 mm | OEM |
After the ride
Tested a change? Record what happened. LAISA stores it against this bike and this condition. The recommendation above does not adapt to it automatically yet.
About this baseline
For a 75 kg Intermediate rider with a Neutral style, the baseline for the Aprilia RSV4 Factory 2024 at Circuito de Navarra shifts one of 19 computed settings away from the OEM standard. The biggest shifts: Rear sprocket 40 teeth (-1 vs OEM). All values are computed from OEM defaults and your rider and condition factors.
Value provenance: OEM = manufacturer specification · verified = confirmed by an expert · reviewed = editorially reviewed reference · community = confirmed by the community (median of at least three public setups) · computed = automatically derived by the LAISA engine. Automatically extracted and unconfirmed values never appear on public pages.
Next steps
Dial in your riding technique
Skills that change how the bike behaves - often the real fix before any clicker.
Explore techniqueMatching protective gear
The right setup is half the job - the other half is protective gear matched to the discipline and conditions.
Gear for these conditionsUpgrades that fit
Optional aftermarket parts for this bike - the setup above comes first, these are next.
Related
Similar bikes
Matching tracks
Frequently asked questions
How much race sag for the Aprilia RSV4 Factory 2024?
As a starting point, 25 mm of race sag at 75 kg rider weight. Measure with a helper and set it via spring preload.
What tire pressure is recommended for the Aprilia RSV4 Factory 2024?
As a starting point: 2.1 bar front, 1.7 bar rear - computed for a 75 kg Intermediate rider. Check cold and adjust in small steps by feel.
What gearing (sprockets) does the Aprilia RSV4 Factory 2024 run?
As a starting point, 16 teeth front / 40 teeth rear. For more acceleration go larger at the rear (or smaller at the front); for more top speed, the reverse.
Are these values safe to ride?
Baseline values are starting points generated from OEM defaults, rider weight, skill, style and conditions - not safety guarantees. Verify on the bike, adjust step by step and ride within your limits.
Baseline values are starting points generated from OEM defaults, rider weight, skill, style, and condition - or lifted from an expert/verified setup where one exists (see the provenance badge). They are not safety guarantees. Verify on the bike and ride within your limits.